marc356
- marc 356
- Posts: 371
- Joined: 06 Jan 2011 20:10
- Contact:
Re: marc356
Richard ,ik had ook twee verschillende maten . Denk dat het tussen de 1 à 2 cm ligt. marc
- Richard
- Moderator
- Posts: 1499
- Joined: 08 May 2006 11:57
- Contact:
- harry
- Posts: 30
- Joined: 13 Jan 2011 20:11
- Contact:
Re: marc356
bij mijn Ctje ziet links er nog netjes (lees origineel) uit en is de afstand 2,2 mm, rechts is behoorlijk 'gedeukt' en is 5 mm
- E10
- Moderator
- Posts: 2473
- Joined: 14 Sep 2008 15:27
- Location: The Netherlands
- Contact:
Re: marc356
Marc, lang niets meer van je gehoord. Hoe staat het ervoor?
- marc 356
- Posts: 371
- Joined: 06 Jan 2011 20:10
- Contact:
Re: marc356
Effe stil gelegen , wel in de goede zin . Wegens mijn werk, zeer druk .Ik ga begin juni verder met de laswerken, probeer hem in september te spuiten (lakken).
Groetjes marc
Groetjes marc
- E10
- Moderator
- Posts: 2473
- Joined: 14 Sep 2008 15:27
- Location: The Netherlands
- Contact:
Re: marc356
Ik ken het.......Dus hij hangt voorlopig nog wel even in de brug?
- marc 356
- Posts: 371
- Joined: 06 Jan 2011 20:10
- Contact:
Re: marc356
Ben vorige zaterdag weer begonnen , de motor ruimte geschuurd en een grondlaag gespoten.
- marc 356
- Posts: 371
- Joined: 06 Jan 2011 20:10
- Contact:
Re: marc356
hier wat foto's
You do not have the required permissions to view the files attached to this post.
- marc 356
- Posts: 371
- Joined: 06 Jan 2011 20:10
- Contact:
Re: marc356
De binnen spatborden vervangen, er kwam toch iets teveel licht door.
You do not have the required permissions to view the files attached to this post.
- marc 356
- Posts: 371
- Joined: 06 Jan 2011 20:10
- Contact:
Re: marc356
Het laswerk links is klaar ,voorste spatbord ,deurdorpel en achterste spatbord.
You do not have the required permissions to view the files attached to this post.
- marc 356
- Posts: 371
- Joined: 06 Jan 2011 20:10
- Contact:
Re: marc356
Zaterdag de kantelbrug van Etienne omgedraaid ,nu de rechterkant aanpakken.
You do not have the required permissions to view the files attached to this post.
- JDMM
- Posts: 2753
- Joined: 07 May 2006 22:14
- Contact:
Re: marc356
Ik denk voor de slinger.
Mooi werk Marc !
Jan.
Mooi werk Marc !
Jan.
If all else fails, read the Workshop Manual !
-
- Posts: 656
- Joined: 07 May 2006 20:35
- Location: Eindhoven The Netherlands
- Contact:
Re: marc356
3e remlicht, Petwin.
If you must reinvent the wheel, remember that it works best if it is, like, roundish.
- marc 356
- Posts: 371
- Joined: 06 Jan 2011 20:10
- Contact:
Re: marc356
Da weet ik ook niet, daarom zit ik op dit forum. Voor de plaat verlichting ?
Deze is ingevoerd uit Frankrijk ,groot vierkant nummerplaat !
Deze is ingevoerd uit Frankrijk ,groot vierkant nummerplaat !
- JDMM
- Posts: 2753
- Joined: 07 May 2006 22:14
- Contact:
Re: marc356
Daar zal dan misschien de "SONAUTO" (Parijse importeur) badge gezeten hebben.
De nummerplaatverling zit in dat rechthoekige gat daar onder.
E10, jij hebt zo'n ding, kun je die eens opmeten ? Ook de steek van de bevestigingsgaatjes.
Jan.
De nummerplaatverling zit in dat rechthoekige gat daar onder.
E10, jij hebt zo'n ding, kun je die eens opmeten ? Ook de steek van de bevestigingsgaatjes.
Jan.
If all else fails, read the Workshop Manual !
Return to “Project van.......”
Who is online
Users browsing this forum: No registered users and 55 guests